Skip to main content

Happy Raksha Bandhan

Happy Raksha Bandhan

 

Happy Raksha Bandhan 2020:

  • चंदन का टीका औ रेशम का धागा,

       सावन की सुगंध औ बारिश की फुहार,

       भाई की उम्मीद और बहन का प्यार,

       मुबारक हो रक्षाबंधन का त्यौहार!!

  • Dearest sister,
       First of all a very "Happy Raksha Bandhan".
       This Raksha Bandhan I promise
       I will always hold your back,
       Whenever you turn back,
       You will find me always.
  • Maa naal ghar sohna lagda.. ??Babul te Veera naal sardari hundi aa.. ????
    Bhain bhave jithe vi rahe..??
    Veera nu jano pyaari hundi aa..????
    HAPPY RAKHRI to every brother and sister...

Stay Home,Stay Safe And Celebrate The Raksha Bandhan With Your Family!!!


Labels:

Comments

Post a Comment

If you have any doubts ,Please let me know.

amazon banner

Popular posts from this blog

Automatic Water Tap Control

Automatic Water Tap Control System Using Arduino Hello, viewers welcome to our new project demonstration.The project title is automatic basin tap control system using Arduino with IR obstacle sensor. The project have another part which is detect the motion and control the light automatically.  Let's see how it is made.  Components list: * Arduino Nano * 16*2 LCD display * Water Tap * IR Sensor * 10k potentiometer * PIR Motion Sensor * 5v LED light * 12v Dc water pump * 12v transformer * BC547 Transistor * 4*2 Battery * On/OFF Switch * 10k Resistor * 100ohm resistor * Veroboard * Some Jumper wire For making this project single Arduino nano-board, 16*2 LCD Display. This is a PIR motion sensor and 5v LED light.The power switch for the circuit. This is another PIR motion sensor and 5v LED light. Here we supply the power using two 4V batteries. This is the rectifier circuit with 12V Auto Dc Transformer. Here we connect the 12V dc water pump motor. This IR obstacle sensor and water ...
2 comments
Read more

Bidirectional Visitor Counter

Bidirectional Visitor Counter using Arduino A bidirectional visitor counter using Arduino may be a reliable circuit that takes over the task of counting variety of Persons/Visitors within the Room very accurately. if somebody enters into the space then the Counter is incremented by one and also leaves it might be incremented. MATERIALS REQUIRED: Arduino IR Module 16*2 LED 5V Relay Resistor(1K,220 ohm) Breadboard Jumper Wires The total number of persons inside the space is Shows on the 16X2 LCD module. The microcontroller does the work it receives the signals from the sensors, and this signals operated under the control of software which is stored in EPROM of Arduino. There are two IR Modules are used. first, one are often wont to count the amount of persons entering a hall within the up mode at the doorway gate. and therefore the other can count the amount of persons leaving the hall by decrementing the count at the exit gate. In this Project will helps to Wastage of electricity. In ou...
Post a Comment
Read more

Motion Detector Camera

Motion Detector With Photo Capture Camera   Hello friends!! Welcome to This Blog. In this Blog, we will make a motion sensor detector with photo capture using ESP32CAM and the PIR module. The logic behind is when the PIR sensor detects any motion, the ESP32CAM will start taking the pictures. So you can use this project as a security camera. In thisblog, I will share the circuitdiagram, Arduino sketch, and the component list, so after reading the complete article you can easily make this project. Now ESP32 CAM is a small camera module that has ESP32S chip on the back and some GPIO pins to connect peripherals and it also has a micro-SD card slot, where you can insert the micro-SD card and store the pictures. Now before going to the circuit diagram and Arduino sketch, let me give you a quick overview of this project.  Components Required ESP32-CAM  PIR Motion Sensor Module BC547 NPN Transistor 220ohm, 1k, 10k Resistor. LED 5-mm FTDI 232 USB to Serial Interface board 5 v...
Post a Comment
Read more